Power Sources and Supplies: World Class Designs

Chapter 1. An Introduction to the Linear Regulator 1.1 Basic Linear Regulator Operation 1.2 General Linear Regulator Considerations 1.3 Linear Power Supply Design Examples Chapter 2. Basic Switching Circuits 2.1 Energy Storage Basics 2.2 Buck Converter 2.3 Boost Converter 2.4 Inverting Boost Converter 2.5 Buck-Boost Converter 2.6 Transformer Isolated Converters 2.7 Synchronous Rectification 2.8 Charge Pumps Chapter 3 DC-DC Converter Design and Magnetics 3.1 DC Transfer Functions 3.2 The DC Level and the “Swing” of the Inductor Current Waveform 3.3 Defining the AC, DC, and Peak Currents 3.4 Understanding the AC, DC and Peak Currents 3.5 Defining the “Worst-case” Input Voltage 3.6 The Current Ripple Ratio ‘r’ 3.7 Relating r to the Inductance 3.8 The Optimum Value of r 3.9 Do We Mean Inductor? Or Inductance? 3.10 How Inductance and Inductor Size Depend on Frequency 3.11 How Inductance and Inductor Size Depend on Load Current 3.12 How Vendors Specify the Current Rating of an Off-the-shelf Inductor and How to Select It 3.13 What Is the Inductor Current Rating We Need to Consider for a Given Application? 3.14 The Spread and Tolerance of the Current Limit 3.15 Worked Example (1) 3.16 Worked Examples (2, 3, and 4) 3.17 Worked Example (5) — When Not to Increase the Number of Turns 3.18 Worked Example (6) — Characterizing an Off-the-shelf Inductor in a Specific Application 3.19 Calculating the “Other” Worst-case Stresses Chapter 4 Control Circuits 4.1 Basic Control Circuits 4.2 The Error Amplifier 4.3 Error Amplifier Compensation 4.4 A Representative Voltage Mode PWM Controller 4.5 Current Mode Control 4.6 A Representative Current Mode PWM Controller 4.7 Charge Pump Circuits 4.8 Multiple Phase PWM Controllers 4.9 Resonant Mode Controllers Chapter 5 Non-Isolated Circuits 5.1 General Design Method 5.2 Buck Converter Designs 5.3 Boost Converter Designs 5.4 Inverting Designs 5.5 Step Up/Step Down (Buck/Boost) Designs 5.6 Charge Pump Designs 5.7 Layout Considerations Chapter 6 Transformer Isolated Circuits 6.1 Feedback Mechanisms 6.2 Flyback Circuits 6.3 Practical Flyback Circuit Design 6.4 Off-Line Flyback Example 6.5 Non-Isolated Flyback Example 6.6 Forward Converter Circuits 6.7 Practical Forward Converter Design 6.8 Off-Line Forward Converter Example 6.9 Non-Isolated Forward Converter Example 6.10 Push-Pull Circuits 6.11 Practical Push-Pull Circuit Design 6.12 Half Bridge Circuits 6.13 Practical Half Bridge Circuit Design 6.14 Full Bridge Circuits Chapter 7 Power Semiconductors 7.1 Introduction 7.2 Power Diodes and Thyristors 7.3 Gate Turn-Off Thyristors 7.4 Bipolar Power Transistors 7.5 Power MOSFETs 7.6 Insulated Gate Bipolar Transistor (IGBT) 7.7 MOS Controlled Thyristor (MCT) 7.8 References 7.9 Bibliography Chapter 8 Conduction and Switching Losses 8.1 Switching a Resistive Load 8.2 Switching an Inductive Load 8.3 Switching Losses and Conduction Loss 8.4 A Simplified Model of the Mosfet for Studying Inductive Switching Losses 8.5 The Parasitic Capacitances Expressed in an Alternate System 8.6 Gate Threshold Voltage 8.7 The Turn-on Transition 8.8 The Turn-off Transition 8.9 Gate Charge Factors 8.10 Worked Example 8.11 Applying the Switching Loss Analysis to Switching Topologies 8.12 Worst-case Input Voltage for Switching Losses 8.13 How Switching Losses Vary with the Parasitic Capacitances 8.14 Optimizing Driver Capability vis-à-vis Mosfet Characteristics Chapter 9 Power Factor Correction 9.1 A Universal Input, 180W, Active Power Factor Correction Circuit Chapter 10 Off-line Converter Design and Magnetics 10.1 Flyback Converter Magnetics 10.2 Forward Converter Magnetics Chapter 11 A “True Sine Wave” Inverter Design Example 11.1 Design Requirements 11.2 Design Description 11.3 Preregulator Detailed Design 11.4 Output Converter Detailed Design 11.5 H Bridge Detailed Design 11.6 Bridge Drive Detailed Design Chapter 12 Thermal Analysis and Design 12.1 Developing the Thermal Model 12.2 Power Packages on a Heatsink (TO-3, TO-220, TO-218, etc.) 12.3 Power Packages Not on a Heatsink (Free Standing) 12.4 Radial-leaded Diodes 12.5 Surface Mount Parts 12.6 Examples of Some Thermal Applications